Burnout buttons and chips

[Crossbones Dennis]

Do you use a burnout switch? I've read where some say it's hard on the engine.

What RPM is yours set at? I think mine's 5000.

I do a very short burnout compared to most.

[W333]

MSD 7AL3. Burnout chip set to 7000 rpm. Lift as soon as they start to hook. Any more than that and you'll shake your teeth out. Or in my case break the pick up tube off the oil pump. (and yes it was welded)

[bracketracing]

my chip is set at 6000. I added one after my first past with my 496. I stabbed the throttle and it saw 8000. P518 about had a heart attack. I think he saw the tack jump. Plugs were shut after the run. Don't know why??

[jeremy341a]

7000rpm. hasn't hurt our engines yet and they get a few runs a year

[sg3526]

7000 on the Roadster and 6500 on the Dragster. Tore a few things up on the dragster, but that was stupidity on my part. The Roadster no problems at all.

[doughboy692]

Tech Talk #79- Are Burnouts Abusing Your Engine?

Category: Tech Talk —


Featured in National Dragster

Written by David Reher




In my recent back-page columns, I’ve focused on the mechanical side of drag racing – cooling systems, lubrication systems, fuel systems, and ignition systems. This time I’m going to address a different topic: How a driver’s burnout technique can affect the engine and chassis.

I’m an engine builder, not a driver, but in more than 40 years in drag racing, I’ve witnessed thousands and thousands of burnouts. I’ve worked with tire engineers in extended test sessions. I’ve watched burnouts performed by championship-winning professionals and by novices at bracket races. Where I really see the effects of burnouts is in the engine shop.

How can burnouts affect engine performance and reliability? I’ve asked myself that question when two identical engines have come back to our shop for overhauls in vastly different conditions. Both engines were assembled with the same components and specifications, both produced virtually the same dyno numbers, and both had made a similar number of runs – yet one looked nearly perfect, and the other was abused almost to the point of failure. In an age of electronically controlled automatic shifters and rpm limiters, how is this possible? I’ve concluded that how a drag racing engine is treated during burnouts has a lot to do with its long-term reliability.

The best procedure is a smooth, driving burnout to clean and heat the tires. It’s essential to back off the throttle before the tires bite. A driver who has a good feel for the car instinctively lets off the gas before the tires grab. If the tires suddenly hook up under power, the result is often instant, violent tire shake. This problem is aggravated by the necessity in sportsman racing to use larger tires due to the widely varying track conditions that sportsmen race under.

In a high-horsepower race car with a manual transmission, the abrupt meeting of horsepower and traction during a burnout will almost invariably knock out the carefully adjusted clutch. In an automatic-equipped race car, the telltale sign is elongated bolt holes and cracks in the flexplate. The evidence can also be seen in the chassis as cracked suspension mounts and bent frame rails. The smooth application of power during a burnout won’t do that.

I don’t recommend using a stepped rpm limiter during the burnout. It’s all right to have a high-speed limiter as a backup to prevent over-revving the engine in case of a broken drivetrain or a stuck throttle. It’s not OK to put the throttle pedal on the floor and run the engine against the limiter for the duration of the burnout.

Limiters work by cutting spark to the cylinders, essentially causing continuous misfires. Many are so effective that they can control the engine speed to within a few rpm. The downside, however, is that the prolonged interruption of the cylinder firing is very hard on an engine. Instead of a steady flow of power pulses being delivered to the crankshaft, the power comes in starts and stops as cylinders are dropped and fired again. The intense vibrations that result are transmitted throughout the engine, affecting the crankshaft, the camshaft drive, and the valvetrain. The driver can’t appreciate what’s happening because the engine is usually popping, banging, and running rough when it’s on the limiter.

Operating an engine at a specific rpm imposed by an rpm limiter for an extended time during a burnout can have serious consequences if the natural frequencies of the components are in sync at that particular engine speed. I’ve learned this from my own experiences. Years ago, my late partner, Buddy Morrison, built a spin fixture to test valvetrain dynamics. It wasn’t nearly as sophisticated as today’s Spintrons, but it did the job. We had a 460ci Ford hooked up to the test engine through a gear drive and spun the crankshaft at whatever rpm we wanted. We’d watch what the valvetrain was doing at various rpm with a 60-cycle strobe light – and sometimes what we saw was shocking!

At certain speeds, the valvetrain would be totally out of control, with the pushrods smoking and the valve springs bouncing completely off the heads and retainers. The particular rpm where these frequencies converged depended on many variables – the pushrod diameter and wall thickness, the valve spring pressure, the camshaft profile, the valve weight, the rocker arm ratio, and many other factors. It was an eye-opening demonstration of the effects of harmonics in a racing engine.

Years later, I was reminded of that experience when Bruce Allen and I were breaking in tires with our Pro Stock on the day after a national event. We’d left our race engine in the car, thinking that a few low-rpm burnouts to scuff new sets of slicks couldn’t possibly damage it.

Well, we just about killed that engine in the span of a few seconds. When I pulled off the rocker covers after the burnouts, there was smoke rolling out of the valley. The valve springs had collapsed, the pushrods were trashed, and we were fortunate we hadn’t destroyed out best engine. Even though the engine was running far below its peak rpm, the particular engine speed that it ran during the tire break-in burnouts produced a perfect storm of valvetrain harmonics.

A racing engine that operates across a range of speeds typically doesn’t spend enough time at a specific rpm point to experience damaging harmonic vibrations. If the engine is electronically held at a prescribed rpm that excites harmonic vibrations by a rev limiter during a burnout, then the result can be internal damage. This damage is cumulative, with the parts deteriorating every time a burnout is done at the same rpm.

When we disassemble an engine and find broken valve springs, damaged pushrod and rocker arm cups, and other signs of harmonic-related distress, it points a finger at the burnout procedure. An identical engine that’s run without a burnout rev limiter may show none of these symptoms because the driver’s right foot can’t hold the rpm at a constant prescribed speed. The problem is that the engine speed where harmonics occur can’t be pinpointed – it depends on the complex interaction of all of the components. Change the pushrod diameter or install a set of beehive valve springs, and the valvetrain dynamics will change as well.

In my experience, most of the engines that are in good condition when they come back for overhaul have been raced by drivers who do smooth burnouts – controlled by the throttle pedal, not by a limiter – and get off the gas before the tires grab. If a racer perfects this technique, the engine will live longer and perform better.



No Comments

No comments yet.

RSS feed for comments on this post.

Sorry, the comment form is closed at this time.